Other Cooper B-Line Product Lines
Cable Tray SystemsStrut Systems (Bolted Framing)ElectricalEnclosuresElectronic EnclosuresSpring Steel FastenersCable Runway& Relay Racks (CommData)Meter Mounting & DistributionEquipmentAnchors
2008 Cooper B-Line, Inc. Printed in U.S.A. 20908
SYSTEMS THAT MAKE SENSE
BB-- VVOOCCAALLSSMM BB-- VVOOCCAALLSSMMQuestions, Comments,Suggestions?
with Cooper B-Line Voice Of the Customer...Actively[emailprotected]
618-654-2184 ext. 456
BB-- VVOOCCAALLSSMM
Pipe Hangers & SupportsPipe Hangers, Pipe Clamps, BeamClamps, Upper Attachments,Pipe Rollers & Roller Supports, PipeSuppors-Guides-Shields-Saddles,Concrete Inserts, Brackets, ThreadedAccessories,Vibra Trol, Roof-Top SupportsPH-08
Cooper B-Line509 West Monroe StreetHighland, IL 62249Phone:800-851-7415Fax: 618-654-1917
www.cooperbline.com
Cooper Industries, Ltd.600 Travis, Ste. 5800Houston, TX77002-1001Phone: 713-209-8400www.cooperindustries.com
Pip
e Hang
ers & S
upp
orts
PH
-08
INTRODUCTION
Cooper B-Line, Inc. is a leading manufacturerand fabricator ofmetal products used in thesupport of pipe and equipment forindustrial,commercial, utility, and OEM installations. CooperB-Lineis proud of the exacting standards ofresearch, design, engineering,and manufacturingthat go into each and every product thatcompriseour pipe hanger product line. Our customers haveaccess tothe most complete support systemsoffered in the industry, includingpipe hangers,metal framing, cable tray, slotted angle,fasteners,telecom, enclosures and anchors.
Many of Cooper B-Line's products are listed byUnderwriters'Laboratories, Inc. All Cooper B-Lineproducts are manufactured tomeet or exceedindustry standards set for their designandmanufacture.
Cooper B-Line products are produced in fourmodern plantsconsisting of over 1,000,000square feet. These facilities arelocated inHighland, Illinois; Troy, Illinois; Reno, Nevada,andSherman, Texas. Regional sales anddistribution centers are locatedthroughout theUnited States stocking standard Cooper B-Lineproductsfor quick service and delivery.
This catalog is designed to be helpful toengineers andcontractors in the application andselection of pipe hanger andsupport products forconstruction and maintenance.
If a unique application requires a special productnot includedin this catalog, Cooper B-Lineengineering personnel are ready tofurnish designconsultation and realistic material estimates.Inaddition, sales representatives with engineeringknow-how arelocated throughout the UnitedStates and abroad for yourconvenience.
Cooper B-Line509 West Monroe StreetP.O. Box 326Highland,Illinois 62249-0326Phone: 800-851-7415
www.cooperbline.com
SINCE
1924
MANUFACTURERS STANDARDIZATION SOCIETYOF THE
VALVE AND FITTING INDUSTRY, INC.
WarningAll hanger products in this catalog are intendedforinstallation and service as illustrated or described. Weareaware that these products have been used successfullyforpurposes other than for which they were designed. We alsoknowthat on occasion, these products have failed whenused as tools forerection or for some purpose other thanintended use. We cautionagainst misapplication which mayresult in failure or accident.
Examples of this misapplication which can result infailureinclude: the use of a beam clamp on a beam otherthandescribed in the catalog; the use of concrete inserts asaanchor for pulling pipe up to the required elevation; andthesuspension of clevis hangers, one under another, which canresultin the accumulative load greater than the pipe hangerwill support.Cooper B-Line pipe hanger products aremanufactured in accordancewith industry standards. Ourcustomers should exercise care to usethese productsproperly so as to avoid an on-the-job accident.Consult theHome Office for assistance of proper installation anduse ofthe products in this catalog.
Your Local Representative Is:
Vibra TrolPads..........................................................170-172Molded Mounts............................................... 172Cup Mounts..................................................... 173SpringMounts ......................................... 174-179VibrationHangers .................................... 180-181Spring Hangers........................................ 182-188Vibra Clamp............................................. 189-190IsolationProducts ........................................... 191
Dura-BlokBase.................................................................193Base & Channel .......................................194-196Base & Clamp Riser....................................... 197Base & Harness....................................... 198-199Base & Rollers......................................... 200-201Base Stand...................................................... 201LoadDistribution Plate .................................. 202
Dura CleanChannel............................................................206Wall Mount Rail ...............................................207U-Bolt & Threaded Rod ..................................208Hardware & Spacers ......................................209
KwikWireClamps.............................................................212Wire Rope........................................................ 212KwikPakKits ...................................................213Accessories..................................................... 214
Hanger Assemblies ...................................216-233Seicmic Assemblies ..................................234-238
Reference DataMetric Conversions........................................ 239Miscellaneous Charts............................. 240-249MSS & FederalSpecifications to
B-Line Cross References .................... 250-251B-LineCompliances & Approvals .......... 252-253Trapeze Hanger Chart.................................... 254
Index...........................................................255-256
Pictorial Index.................................................. 2-13
Strut Systems Information ............................ 14-15
Technical DataMaterials............................................................16Corrosion...........................................................16Finishes ........................................................16-17General Information ..........................................17Recommended Specifications ................... 18-23
Beam ClampsC-Clamps..................................................... 25-29BottomBeam Clamps ................................. 29-34Top Beam Clamps............................................. 35Trus Joist &Angle Iron Beam Clamps ............ 36
Pipe Hangers'J' Hangers........................................................ 39ClevisHangers ............................................ 40-47BandHangers .............................................. 48-50SplitClamps & Hangers, Rings .................. 51-58Wall MountLay-In Hangers ........................ 55-56Spring Hangers................................................. 57
Pipe ClampsRisers............................................................61-62Underground Clamps ..................................63-64Clamps.........................................................65-69Straps...........................................................70-71
Pipe Rollers & Roller SupportsRoller Hangers............................................. 73-74Roller Supports............................................ 75-83Roller Stands............................................... 84-86Spring CushionRoller Hanger ......................... 87Rollers..........................................................88-89
Pipe Supports, Guides, Shields & SaddlesCalcium SilicateShields ................................... 91Stands & Supports.................................... 92-103Guides & Anchors................................... 104-109Slides, Shields, Saddles.......................... 110-126
Concrete InsertsAnchor Bolt Insert.......................................... 129Spot Inserts &Nuts ................................. 130-136Anchor Clips.................................................... 137
BracketsLight Duty........................................................ 139MediumDuty ................................................... 140HeavyDuty ...................................................... 141
Upper AttachmentsCeiling Flange................................................. 143Angle Supports........................................ 143-145Bolted & Welded...................................... 146-147Concrete Plates....................................... 148-150Rod Beam Attachments................................. 151
Threaded AccessoriesU-Bolts.....................................................154-155Miscellaneous Accessories ............ 153, 156-158Rods,Couplings & Washers ................... 159-166
Table of Contents
1
Figure B351LSteel C-ClampWith Locknut
Page 25
Figure B3036LMalleable Iron
C-ClampWith Locknut
Page 25
Figure B3362 thru B3365
Retaining StrapPage 26
Figure B3031-3/8Light Duty
Malleable C-ClampPage 26
Figure B3033Wide Jaw
Top Flange C-ClampPage 27
Figure B3034Top Flange C-Clamp
Page 28
Figure B3042Top Beam Clamp
Page 35
Figure B312Retaining Strap
Page 30
Figure B3050Beam Clamp
Page 32
Figure B3045Side Beam Clamp
Page 35
Figure B3037Z-Purlin Beam Clamp
Page 26
Figure B3052Trus Joist
Beam ClampPage 36
Figure B303-B309Beam Clamp
Page 29Figure B321 Series
Beam ClampPage 29
Figure B3367Retaining Strap
Page 30
Figure B3291 thru B3298UFS Forged Steel
Beam ClampPage 34
Figure B3054Malleable Iron Beam Clamp
Page 33
BEAM CLAMPS
Figure B3055Steel Beam Clamp
Page 31P
ictorial Index
Figure B3040Adjustable Beam Clamp
Page 30
Pictorial Index
2
u Dura-Copper FinishX Dura-Green Finish
Figure B3106Vee Bottom
Clevis HangerPage 47
Figure B3106VPlastic Pipe
Support ChannelPage 47
Figure B3108Extended
Clevis HangerPage 45
Figure B3109Flat Top Clevis
HangerPage 46
Figure B3690Adjustable 'J' Hanger
Page 39Figure B3690CPlastic Coated
Adjustable 'J' HangerPage 39
Figure B3690FFelt Lined
Adjustable 'J' HangerPage 39
Figure B3104Light Duty Clevis Hanger
Page 42Figure B3104CTCopper Tubing
Light Duty Clevis HangerPage 43
Figure B3104CPlastic Coated
Light Duty Clevis Hanger
Page 42Figure B3104CTC
Copper TubingPlastic Coated
Light Duty Clevis Hanger
Page 43Figure B3104F
Felt LinedLight Duty
Clevis HangerPage 42
Figure B3100Standard Clevis Hanger
Page 40 & 41Figure B3100CPlastic Coated
Standard Clevis HangerPage 40 & 41
Figure B3100FFelt Lined
Standard Clevis HangerPage 40 & 41
Figure B3102AWWA Clevis Hanger
Page 44
PIPE HANGERS
u
XX
u
Pic
toria
l Ind
ex
Pictorial Index
3
PIPE HANGERS (Continued)
Figure B3198HHinged ExtensionSplit Pipe Clamp
Page 51Figure B3198HCT
Copper TubingHinged ExtensionSplit Pipe Clamp
Page 52 u
Figure B3198PFigure B3198R
ExtensionSplit Pipe Clamp
Page 51Figure B3198RCT
Copper TubingExtension
Split Pipe ClampPage 52 u
Figure B3175Ring and Bolt Hanger
Page 53Figure B3175CTCopper Tubing
Ring and Bolt HangerPage 53 u
Figure B3170CTCopper Tubing
Adjustable Swivel RingPage 510
Figure B3170CTCCopper TubingPlastic Coated
Adjustable Swivel RingPage 50
u
u
Figure B3170Adjustable Swivel Ring
Page 49
Figure B3170NFAdjustable
Swivel Ring(NFPA Rod Sizes)
Page 48
Figure B3170NFFFelt LinedAdjustable
Swivel Ring(NFPA Rod Sizes)
Page 48
u Dura-Copper Finish
Pictorial Index
Pictorial Index
4
Figure B3170NFCPlastic Coated
AdjustableSwivel Ring
(NFPA Rod Sizes)Page 48
Figure B3191Straight 'J' Hook
Page 56
Figure B386 Suspension Rod
Pipe ClampPage 55
Figure B3171Adjustable Split
Ring Swivel HangerPage 54
Figure B3262Light Duty
Spring HangerPage 57
Figure B3190Offset 'J' Hook
Page 56
PIPE CLAMPS
Figure B3373Standard Riser Clamp
Page 61
Figure B3373CTCopper TubingRiser Clamp
Page 62
Figure B3373CPlastic Coated
Standard Riser ClampPage 61
Figure B3373CTCCopper TubingPlastic CoatedRiser Clamp
Page 62u u
Figure B3132Two-Bolt
Underground ClampPage 63
Figure B3132WLug Washer
Page 63
Figure B3134WWasherPage 64
Figure B3134Four-Bolt
Underground ClampPage 64
Figure B3140Standard Pipe Clamp
Page 65
Figure B3142Heavy Duty Pipe Clamp
Page 66
XX
PIPE HANGERS (Continued)
Figure BH-2-4BH-5-8BH-9-12
Parallel Strap HangerPage 58
Figure BH-2-4-RBH-5-8-R
BH-9-12-RRight Angle Strap Hanger
Page 58
Figure BL1400thru BL1490
HangerPage 58
u Dura-Copper FinishX Dura-Green Finish
Pic
toria
l Ind
ex
Pictorial Index
5
Figure B3148Offset Pipe Clamp
Page 69Figure B3149Marine Hanger
Page 69
Figure B2400Standard Pipe Strap
Page 70-71
Figure B3144Double Bolt Pipe Clamp
Page 67Figure B3146
Heavy Duty Double Bolt Pipe Clamp
Page 68
Figure B3110Adjustable SteelYoke Pipe Roll
Page 73
Figure B3120Roller Chair
Page 77
Figure B3114Pipe Roll With Sockets
Page 74Figure B3122
Adjustable Roller SupportPage 75
Figure B3124Roller Support
Page 78
Figure B218Pipe Rollers
Page 80
Figure B219Pipe Rollers
Page 81Figure B3126Roller Support
Page 79
PIPE ROLLERS & ROLLER SUPPORTS
Figure B379Pipe Rollers
Page 82
Figure B479Pipe Rollers
Page 83Figure B3118SL
Adjustable Roller StandWith Base Plate
Page 85
Figure B3119SLRoller With Steel
Base PlatePage 86
Figure B3117SLSteel Roller Stand
Page 84
Figure B3114RLong Pipe Roll Only
Page 88Figure B3264
Spring Cushion HangerPage 87
Figure B3122AAdjustable Double
Roller GuidePage 76X
X Dura-Green Finish
Pictorial Index
Figure B3117RShort Pipe Roll Only
Page 88
Pictorial Index
6
Figure B3088Base Stand
Page 92Figure B3088S
Seismic Base StandPage 93
Figure B3088TThreaded Base Stand
Page 92Figure B3088ST
Seismic ThreadedBase Stand
Page 93
Figure B3089Pipe Support Adjuster
Page 95
Figure B3090Pipe Saddle Support
With U-BoltPage 96-97
Figure B3095Pipe Saddle Support
Page 98-99
Figure B3096Adjustable PipeSaddle Support
Page 94
Figure B3092Adjustable Pipe Saddle
Support With YokePage 100-101
Figure B3093Adjustable PipeSaddle SupportPage 102-103
Figure B3281 thruB3287
Pipe AlignmentGuide
Pages 104 & 105
PIPE SUPPORTS, GUIDES, SHIELDS & SADDLES
Figure B3380thru B3384
360 Calcium SilicateShield
Page 91
Figure B3147AFigure B3147BAnchor ChairsPage 106-107
Figure B2417Pipe Guides
Page 106
Figure B3256Hold-Down
Anchor ClampPage 108
Pic
toria
l Ind
ex
Pictorial Index
7
Figure B3257Base PlatePage 109
PIPE SUPPORTS, GUIDES, SHIELDS & SADDLES (Continued)
Figure B3151Insulation
Protection ShieldPage 125
Figure B3891 thru B3897Pipe Slides
Pages 110-113
Figure B3153Insulation Protection
Shield With TabsPage 125
Figure B3155Short Insulation
Protection ShieldWith TabsPage 126
Figure B3160 thruB3165
Pipe CoveringProtection Saddle
Pages 118-123
Figure B3991 thruB3993
Pipe SlidesPages 114-117
Figure B3154Short Insulation
Protection ShieldPage 126
Figure BE-5-8Fastener Clip
Page 137
Figure B2500Light Duty Spot Insert
Page 130
Figure N2500Steel Insert Nut
Page 130
Figure B2501Light Duty Spot Insert
Page 129
Figure B3014Malleable Iron
Spot InsertPage 131
Figure B3014NMalleable Iron Insert Nut
Page 131
CONCRETE INSERTS
Figure B2503Heavy Duty Spot Insert
Page 133 Figure B22I, B32I, B52IContinuous Concrete InsertsPages134 - 136
Figure B3019Adjustable MetalDeck Ceiling Bolt
Page 129 Figure B2505thru B2508Spot InsertPage 132
Figure BD40Fastener Clip
Page 137
Pictorial Index
Pictorial Index
8
BRACKETS
Figure B3064Adjustable Strut Bracket
Page 139
UPPER ATTACHMENTS
Figure B3068Light Duty Bracket
Page 139
Figure B3199Ceiling Flange
Page 143
Figure B3199CTDura-Copper Coated
Ceiling FlangePage 143
Figure B3058Side Beam Connector
Page 145
Figure B3062Side Beam Bracket
Page 145
Figure B3060Side Beam Angle Clip
Page 143Figure B3070
Reversible Angle ClipPage 144
Figure B3060LSide Beam Angle Clip
Page 144u
u Dura-Copper Finish
Pic
toria
l Ind
ex
Figure B3067Heavy Duty Angle Bracket
Page 141
Figure B3066Medium Duty Angle
BracketPage 140
Pictorial Index
9
Figure B3080S (Short)Figure B3080L (Long)Structural WeldingLug
Page 147
Figure B3083Figure B3083WO
Welded Beam AttachmentPage 146
Figure B3084Single Lug Concrete Plate
Page 150
Figure B3085Rod Attachment Concrete Plate
Page 148
Figure B3086Clevis Concrete Plate
Page 149Figure B3082
Rod Beam AttachmentPage 151
THREADED ACCESSORIES)
Figure B3188Standard U-Bolt
Pages 153 & 154
Figure B3188CPlastic Coated
Standard U-BoltPages 153 & 154
Figure B3222Eye SocketPage 153
Figure B3201Forged Steel Clevis
Page 156
Figure B3200Weldless Eye Nut
Page 153
Pictorial Index
Pictorial Index
10
Figure B3223Offset Eye Socket
Page 157Figure B3203
Extension PiecePage 157 Figure B3202
TurnbucklePage 158
Figure B3224Hanger Adjuster
Page 158Figure B3224CT
Dura-Copper CoatedHanger Adjuster
Page 158 u
Figure B3210Eye RodPage 160
Figure B3211Welded Eye Rod
Page 160
Figure B3210XLinked Eye Rod
Page 161Figure B3211X
Linked Welded Eye RodPage 161
Figure B3205Machine Threaded Rod
Page 159
Figure B3212J-Bolt
Page 162
u Dura-Copper Finish
Figure B3228Hex Head Lag Bolt
Page 163
Figure DS 16 x 2#16 x 2" Drive Screw
Page 163Figure B3213Coach Screw RodPage 162
Figure B3227Flat End Lag Screw
Page 163
Figure ATRAll Threaded Rod
Page 159
THREADED ACCESSORIES (Continued)
VIBRA TROL
Pic
toria
l Ind
ex
Pictorial Index
11
Figure NNPRibbed
Neoprene PadPage 170
Figure VRPRubber Cube Pad
Page 171
Figure CNNKCork, Ribbed
Neoprene and SteelPage 171
Figure CNPCork and RibbedNeoprene Pad
Page 170
Figure BVSVibra Strip for 15/8" Wide B-Line channel
Page 172
Figure NVDDouble Deflection
Page 172
Figure CMMetal Housing and
NeoprenePage 173
Figure B3220Malleable IronRod Coupling
Page 164
Figure B655Steel Rod Coupling
Page 164Figure B656
Steel Reducer Rod Coupling
Page 164
Figure B3234Bevel Washer
Page 166
Figure B3248Steel Washer Plate
Page 165
Figure B200Square Washer
Page 165
Figure ANHAcoustical Hanger
Page 180
Figure HMLT/HMTHoused 1"
Deflection MountingPages 178 & 179
Figure OML/OMSpring Mount
Pages 174 & 175
Figure HMLE/HMEHoused 1"
Deflection MountingPages 176 & 177
VIBRA TROL (Continued)
DURA-BLOK
Pictorial Index
Pictorial Index
12
Figure SHEIsolation Spring Hanger
Pages 186 & 187
Figure HSL/HSVibration Spring Hanger
Pages 182 & 183
Figure RHNeoprene Hanger
Page 181Figure HESL/HES
Combination Spring & NeoprenePages 184 & 185
Figure BVTVibraclamp Tubing Sizes
Page 189Figure BVP
Vibraclamp Pipe SizesPage 190
Figure B1999Vibra Cushion
Page 191
BasesPage 193
Figure ISOISO PipePage 191
Base & Short ChannelPage 194 Base & Tall Channel
Page 195Double Base & Long Channel
Page 196
Base & Clamp RiserPage 197 Bases & Harness Assembly
Page 198-199
Base & Fixed HeightRoller Assembly
Page 200Base & Adjustable Height
Roller AssemblyPage 201
DURA-BLOK (Continued)
DURA-CLEAN
KWIKWIRE
Pic
toria
l Ind
ex
Pictorial Index
13
Base & AdjustabelHeight Channel
Page 201
Load Distribution PlatePage 202
ChannelsPage 206
Wall MountRails
Page 207
KwikWire ClampsPage 212
KwikPak KitsPage 213
Wire RopePage 212
Air Duct Corner ProtectorPage 214 Wire Rope Cutter
Page 214Air Duct Support
Page 214
U-BoltsPage 208
HardwarePage 209
SpacersPage 209
All ThreadedRods
Page 208
Cooper B-Line's metal framing support system is designed withmanytime-saving features. Fully adjustable and reusable, with acomplete lineof channels, fittings, and accessories formulti-purpose applications.
SELECTION CHARTfor Channels, Materials and Hole Patterns
Material & Thickness* Channel Hole Pattern **Channel
Stainless SH S H17/8 TH KO6Dimensions
Steel
B11 31/4" (82.5) 15/8" (41.3) 12 Ga. -- -- -- 1 1 1 -- 1B1227/16" (61.9) 15/8" (41.3) 12 Ga. .105 -- -- 1 2 1 1 2 -- 1 2B2215/8" (41.3) 15/8" (41.3) 12 Ga. .105 12 Ga. 12 Ga. 1 2 3 4 1 1 2 34 1 1 2B24 15/8" (41.3) 15/8" (41.3) 14 Ga. .080 14 Ga. 14 Ga. 1 23 4 1 1 2 3 4 -- 1 2B26 15/8" (41.3) 15/8" (41.3) 16 Ga. -- -- -- 11 1 -- 1B32 13/8" (34.9) 15/8" (41.3) 12 Ga. -- 12 Ga. -- 1 3 1 1 3-- 1 B42 1" (25.4) 15/8" (41.3) 12 Ga. -- 12 Ga. -- 1 3 1 1 3 --1B52 13/16" (20.6) 15/8" (41.3) 12 Ga. -- -- -- 1 1 1 -- 1B5413/16" (20.6) 15/8" (41.3) 14 Ga. .080 14 Ga. 14 Ga. 1 2 3 4 1 1 23 4 -- 1 2B56 13/16" (20.6) 15/8" (41.3) 16 Ga. -- -- -- 1 1 1 --1
ChannelType
Steel
1
Alum.
2
Type304
3
Type316
4
Height Width
Channel Nuts
Size and Part Number
Thread With Without TwirlSize Spring Spring Nut
1/4"-20 N224 N224WO TN2243/8"-16 N228 N228WO TN2281/2"-13 N225N225WO TN2255/8"-11 N255 N255WO --3/4"-10 N275 N275WO --
Schedule 40 Pipe Clamps
Copper Tubing ClampsDura Copper
Available Finishes: Electro-Galvanized, Aluminum,Stainless,Dura-Copper Painted, Hot-Dip Galvanized and PVC coated.Nut and bolts are included with all two-piece clamps.** Add PA toPart No. for Pre-assembled
Available Finishes: Electro-Galvanized
B2000 Series
Part Nominal Mat'lNo. Tubing Size Ga.
B2026DCU 1/2" (15) 16B2008DCU 3/4" (20) 16B2030DCU 1" (25)14B2032DCU 11/4" (32) 14B2011DCU 11/2" (40) 14B2038DCU 2" (50)12B2042DCU 21/2" (60) 12B2046DCU 3" (80) 12B2050DCU 31/2" (90)12B2054DCU 4" (100) 11
Part Nomina l Mat'lNo. Pipe Size Ga.
B2001 3/8" (10) 16B2008 1/2" (15) 16B2009 3/4" (20) 14B2010 1"(25) 14B2011 11/4" (32) 14B2012 11/2" (40) 12B2013 2" (50) 12B201421/2" (60) 12B2015 3" (80) 12B2016 31/2" (90) 11B2017 4" (100)11B2018 41/2" (115) 11B2019 5" (125) 11B2020 6" (150) 11B2021 7"(175) 11B2022 8" (200) 11
Strut S
ystems
Information
Strut Systems
14
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Combo Nut Washers
Part ThreadNumber Size
NW524 1/4"-20NW528 3/8"-16NW525 1/2"-13
Available Finishes: Electro-Galvanized
Below are some basic clamp and cushions to be used with a strutsystem. For the industry's most completeline of strut and strutfittings, refer to Cooper B-Line's Strut Systems EngineeringCatalog.
O.D. Pipe Clamps
For Rigid Conduit or Iron Pipe
B1999Vibra-Cushion
Inhibits Galvanic Reaction Reduces Sound & Vibration Used onrefrigeration, HVAC, copper
tubing, glass pipes & hydraulic linesAvailable in 20 Ft.rolls.
B-LINE
B-LINE
BVP150
BVP150
1 1/2 I.P
1 1/2 I.P.
BVT & BVPSeries
Vibra-ClampsAvailable for tubing andpipe sizes 1/4" to 6",ODsizes 1/4" to 65/8". Easyone tool installation,dampens vibrationandnoise, secures tubingfirmly, and protectsagainstgalvanicreaction.Stainless Steel available
Part O.D. Size Mat'lNo. (Outside Dia.) Ga.
B2023 1/4" (6.3) 16B2024 3/8" (9.5) 16B2025 1/2" (12.7) 16B20265/8" (15.9) 16B2027 3/4" (19.0) 16B2028 7/8" (22.2) 16B2029 1"(25.4) 14B2030 11/8" (28.6) 14B2031 11/4" (31.7) 14B2032 13/8"(34.9) 14B2004 11/2" (38.1) 14B2011 15/8" (41.3) 14B2005 13/4"(44.4) 12B2036 17/8" (47.6) 12B2037 2" (50.8) 12B2038 21/8" (54.0)12B2039 21/4" (57.1) 12
Nominal Length of UseSize Vibra-Cushion Clamp No.
3/8" (10) 21/8" (54.0) B20021/2" (15) 25/8" (66.7) B20093/4"(20) 31/4" (82.5) B20311" (25) 41/8" (104.8) B2004
11/4" (32) 53/16" (131.8) B201211/2" (40) 515/16" (150.8)B20382" (50) 71/2" (190.5) B2042
21/2" (65) 9" (228.6) B20463" (80) 11" (279.4) B2051
31/2" (90) 121/2" (317.5) B20554" (100) 141/2" (368.3) B20595"(125) 177/16" (442.9) B20676" (150) 203/4" (527.0) B2116
For Thinwall (EMT) Conduit
Nominal Length of UseSize Vibra-Cushion Clamp No.
3/8" (10) 113/16" (46.0) B20271/2" (15) 23/16" (58.7) B20023/4"(20) 27/8" (73.0) B20031" (25) 35/8" (92.1) B2032
11/4" (32) 43/8" (120.6) B203611/2" (40) 57/16" (138.1) B20122"(50) 67/8" (174.6) B2013
For Copper Tubing Type L & K
Nominal Length of UseSize Vibra-Cushion Clamp No.
1/4" (6) 13/16" (30.2) B20263/8" (10) 19/16" (39.7) B20271/2"(15) 17/8" (47.6) B20285/8" (17) 25/16" (58.7) B20293/4" (20) 23/4"(69.8) B20301" (25) 31/2" (88.9) B2032
11/4" (32) 45/16" (109.5) B201111/2" (40) 51/8" (130.2) B20362"(50) 611/16" (169.9) B2013
21/2" (65) 81/4" (209.5) B20143" (80) 913/16" (249.2) B2048
31/2" (90) 113/8" (288.9) B20524" (100) 1215/16" (328.6) B20565"(125) 61/8" (409.6) B20646" (150) 191/4" (488.9) B21128" (200)251/2" (647.7) B2128
For Copper Tubing & OD Sizes
For Pipe Sizes
Catalog Copper & Steel NominalNo. OD Tubing Size CopperSize
BVT025 1/4" (6.3) -- --BVT037 3/8" (9.5) 1/4" (6)BVT050 1/2"(12.7) 3/8" (10)BVT062 5/8" (15.9) 1/2" (15)BVT075 3/4" (19.0) 5/8"(17)BVT087 7/8" (22.2) 3/4" (20)BVT100 1" (25.4) -- --BVT112 11/8"(28.6) 1" (25)BVT125 11/4" (31.7) -- --BVT137 13/8" (34.9) 11/4"(32)BVT150 11/2" (38.1) -- --BVT162 15/8" (41.3) 11/2" (40)BVT17513/4" (44.4) -- --BVT187 17/8" (47.6) -- --BVT200 2" (50.8) ----BVT212 21/8" (54.0) 2" (50)BVT225 21/4" (57.1) -- --BVT250 21/2"(63.5) -- --BVT262 25/8" (66.7) 21/2" (65)BVT300 3" (76.2) ----BVT312 31/8" (79.4) 3" (80)BVT362 35/8" (92.1) 31/2" (90)BVT4004" (101.6) -- --BVT412 41/8" (104.8) 4" (100)BVT612 61/8" (155.6)6" (150)
Catalog NominalNo. Pipe Size
BVP025 1/4" (6)BVP037 3/8" (10)BVP050 1/2" (15)BVP075 3/4"(20)BVP100 1" (25)BVP125 11/4" (32)BVP150 11/2" (40)BVP200 2"(50)BVP250 21/2" (65)BVP300 3" (80)BVP350 31/2" (90)BVP400 4"(100)BVP500 5" (125)BVP600 6" (150)
B2000 Series
Str
ut S
yste
ms
Info
rmat
ion
Part O.D. Size Mat'lNo. (Outside Dia.) Ga.
B2013 23/8" (60.3) 12B2041 21/2" (63.5) 12B2042 25/8" (66.7)12B2043 23/4" (69.8) 12B2014 27/8" (73.0) 12B2045 3" (76.2) 12B204631/8" (79.4) 12B2047 31/2" (82.5) 12B2048 33/8" (85.7) 12B201531/2" (88.9) 12B2050 35/8" (92.1) 11B2051 33/4" (95.2) 11B205237/8" (98.4) 11B2016 4" (101.6) 11B2054 41/8" (104.8) 11B2055 41/4"(107.9) 11B2056 43/8" (111.1) 11B2017 41/2" (114.3) 11B2058 45/8"(117.5) 11B2059 43/4" (120.6) 11B2060 47/8" (123.8) 11B2061 5"(127.0) 11B2062 51/8" (130.2) 11B2063 51/4" (133.3) 11B2064 53/8"(136.5) 11B2065 51/2" (139.7) 11
Strut Systems
15
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
MATERIALSCarbon Steel
Carbon steel is used in themanufacture of Cooper B-Linepipehangers and supports. Excellentstrength characteristicsandadaptability to cold forming provide awel engineered design. Bycoldforming the steel, mechanicalproperties are increased, addingtothe structural integrity of thefabricated hanger.
Stainless Steel
AISI Type 304 and Type 316 arenon-magnetic members oftheaustenitic stainless steel group.Several conditions make the useofstainless steel ideal. These includereducing long termmaintenancecosts, high ambient temperatures,appearance, and stablestructuralproperties such as yield strength,and high creepresistance.
CORROSIONAll metal surfaces exposed to theenvironment areaffected bycorrosion. Depending on the physicalproperties of themetal and itsproximity to other dissimilar metals,anelectrochemical reaction mayoccur which causes an attack onthemetal itself, resulting in corrosion.Chemical corrosion islimited tohighly corrosive environments, hightemperatures, or acombination ofboth.
FINISHESZinc Coatings
Protective zinc coatings are availableon a number of pipehangers andaccessories in three basic forms:
but is suitable for extended exposure indry or mildly corrosiveatmospheres.
Hot-Dip Galvanized AfterFabrication (ASTM A 123)
After a pipe hanger or fitting has beenfabricated, it iscompletely immersed ina bath of molten zinc. A metallurgicalbond isformed, resulting in a zinccoating that completely coatsallsurfaces, including edges. Zinccoatings of this specificationhave aminimum thickness of 1.50 ounces persquare foot (0.45 kg/m2)on each sideor a total of 3.0 ounces per square foot(0.9 kg/m2) ofsteel.Hot-dip galvanized after fabrication isrecommended foroutdoor exposure.For best results, a zinc rich paint(available fromCooper B-Line) shouldbe applied to field cuts. The zinc richpaintwill provide immediate protectionfor field cuts and eliminate theshorttime period for galvanic action to "heal"the damagedcoating.
Plastic Coating
Some products offered by CooperB-Line are plastic or vinylcoated for prevention of galvanic reaction betweenmaterials or fornoise reduction. Thesecoated products can also be usedwhere contactbetween glass pipe andhanger is not desirable. Felt linedhangersmay be substituted for samepurpose.
Red Primer
A corrosion resistant metal primercontaining rust inhibitivepigments.
Electro-Plated Zinc, Pre-Galvanized,and Hot-Dip GalvanizedAfterFabrication. In all cases, the zincprotects the steel first asa sacrificialanode to repair bare areas on cutedges and gouges.Whenexposed to air and moisture,zinc forms a tough, adherentprotectivefilm consisting of a mixture of zincoxides, hydroxides,and carbonates.The corrosion resistance of zinc isdirectly relatedto its thickness and theenvironment. For example a 0.2 mil(5 m)coating will last twice as longas a 0.1 mil (2.5 m) coating inthesame environment.
Electro-Plated Zinc(ASTM B 633 SC1 or SC3)
An Electro-Plated process depositsa coating of zinc on the steelbyelectrolysis from a bath of zinc salts.This coating is pure zincand adheresto the steel with a molecular bond. Amaximum of 0.5 mils(12.7 m) of zinccan be applied by this method. Thiscoating isrecommended for in-dooruse in relatively dry areas.
Pre-Galvanized Zinc(ASTM A 653 CoatingDesignation G90)
Pre-galvanized zinc is produced bycontinuously rolling the steelcoils orsheets through molten zinc at the steelmills. This is alsoknown as "mill-galva-nized" or "hot-dipped mill galvanized".Coilsare then slit to size for fabricationof pipe hangers. Coatingthicknessesof G90, is 0.90 ounces per square foot(0.27 kg/m2) ofsteel surface.
Cut edges and welded areas are not zinc coated; however, zincnear theuncoated metal becomes a sacrificial anode which protectsthebare areas after a short period of time.Pre-galvanized steel isnot generally recommended for use outdoors in industrialenvironments,
Protection of cut edges with zinc coatings.
Zn
Fe
ZnFe
ZnOTechnical D
ata
Technical Data
16
General InformationTorque
The torque values in this catalog are to be used as a guideonly. The relationship between the applied torque ortorque wrenchreading and the actual tension created in the bolt may besubstantially different. Important factorsaffecting torque-tensionrelationships include friction under the bolt head or nut, holetolerances, and torquewrench tolerances. Accuracy of manycommercial torque wrenches may vary as much as plus or minus25%.
Charts and Tables
Charts and tables in this section are compiled from informationpublished by nationally recognized organizationsand are intendedfor use as a guide only. Cooper B-Line recommends that users ofthis information determinethe validity of such information asapplied to their own applications.
Cooper B-Line, Inc. reserves the right to make specificationchanges without notice.
DURA-COPPER & DURA-GREEN EPOXY COATING PROCESS
SALT SPRAY TEST RESULTS
(1) All salt spray (fog) tests conducted in accordance with ASTMB 117-73 and evaluated and ratedaccording to ASTM D 1654-79 Tables1 & 2. Tests were performed and certified by an independenttesting laboratory.
Dura-Copper and Dura-Green Epoxy Coatings
Dura-Copper and Dura-Green arewater borne epoxy coatings appliedtoCooper B-Line products by a preciselycontrolled cathodicelectro-depositionprocess. This process is accomplishedusing aconveyor to transport partsthrough several cleaning,phosphatizingand application stages prior to beingbaked (Seediagram below).This custom designed paint system isused forpainting all copper paintedhanger parts and all greenchannel,slotted angle and fittings.
Samples are selected on a routinebasis for Salt Spray (fog)testing toverify the quality of the finish. Thesetests areperformed in accordance withASTM B 117-73 and evaluated andratedaccording to ASTM D 1654-79(Tables 1 & 2). The Dura-CopperandDura-Green Epoxy coatings havebeen tested and listed byUnderwritersLaboratories in accordance with"Standard for PipeHanger Equipmentfor Fire Protection Service, UL 203"and meet orexceed all requirements ofFederal Specification TT-C-490BParagraph3.
Quality Assurance
Cooper B-Line System's QualityAssurance Program hasbeendeveloped and implemented forcompliance to variousindustrystandards and specifications.
Dura-CopperEpoxy
Copper Plating
Elapsed Time
TANK 1
Parts are thor-oughly cleanedand phospha-tized.
TANK 2
Rinse isapplied toremoveinsoluble saltsandunreactedphosphates.
TANK 3
Phosphatizedsealer is appliedto insurecorrosion resis-tance andpaintadhesion.
TANK 4
The materialmoves throughclear waterrinse to removeexcessphos-phates.
TANK 5
Deionized rinseprepares themetal forthecathodicelectro-coating.
TANK 6
The electro-coating tankapplies a uniform coat ofepoxy painttothe entire sur-face.
TANK 7
The first post rinseremovesanyunelectricallyattractedsolids.
TANK 8
The final rinseinsures asmooth, nonblemish finish.
BAKE OVEN
The curingprocess takes20 minutes at abaking temperature of375F(199C).
Dura-Copperout performs
Copper Plating 4 to 1
Tech
nica
l Dat
a
Technical Data
17
Part I - GENERAL
1.01 SECTION INCLUDES
A. The work covered under this section consists of thefurnishing of all necessary labor,supervision, materials,equipment, and services to completely execute the pipe hanger andsupports as described in this specification.
1.02 REFERENCES
A. ASTM B 633 - Specification for Electrodeposited Coatings ofZinc on Iron and Steel.B. ASTM A 123 - Specification for Zinc(Hot-Dip Galvanized) Coatings on Iron and Steel Products.C. ASTM A653 - Specification for Steel Sheet, Zinc-Coated (Galvanized) orZinc-Iron
Alloy-Coated (Galvannealed) by the Hot-Dip Process.D. ASTM A1011 - Specification for Steel, Sheet and Strip, Hot-Rolled,Carbon, Structural,
High-Strength Low-Alloy, and High-Strength Low-Alloy withImproved Formability.E. MSS SP-58 - Manufacturers StandardizationSociety: Pipe Hangers and Supports - Materials,
Design, and Manufacture.F. MSS SP-69 - ManufacturersStandardization Society: Pipe Hangers and Supports - Selection
and Application.G. NFPA 13 - Installation of SprinklerSystems.
1.03 QUALITY ASSURANCE
A. Hangers and supports used in fire protection piping systemsshall be listed and labeled byUnderwriters Laboratories.
B. Steel pipe hangers and supports shall have the manufacturersname, part number, andapplicable size stamped in the part itselffor identification.
C. Hangers and supports shall be designed and manufactured inconformance with MSS SP-58.D. Supports for sprinkler piping shallbe in conformance with NFPA 13.
1.04 SUBMITTALS
A. Submit product data on all hanger and support devices,including shields and attachmentmethods. Product data to include,but not limited to materials, finishes, approvals, loadratings, anddimensional information.
Part II - PRODUCTS
2.01 ACCEPTABLE MANUFACTURERS
A. Manufacturer: Subject to compliance with thesespecifications, pipe hanger and supportsystems shall be asmanufactured by Cooper B-Line, Inc.
2.02 PIPE HANGERS AND SUPPORTS
A. Hangers1. Uninsulated pipes 2 inch and smaller:
a. Adjustable steel swivel ring (band type) hanger, CooperB-Line B3170.b. Adjustable steel swivel J-hanger, Cooper B-LineB3690.c. Malleable iron ring hanger, Cooper B-Line B3198R or hingedring hanger, B3198H.d. Government type hanger, Cooper B-Line B3225or B3226.e. Adjustable steel clevis hanger, Cooper B-Line B3104 orB3100.
SECTION 15140 - PIPE HANGERS AND SUPPORTS
Technical Data
Technical Data
18
2. Uninsulated pipes 21/2 inch and larger:a. Adjustable steelclevis hanger, Cooper B-Line B3100.b. Pipe roll with sockets,Cooper B-Line B3114.c. Adjustable steel yoke pipe roll, CooperB-Line B3110.
3. Insulated pipe - Hot or steam piping:a. 2 inch and smallerpipes: use adjustable steel clevis with galvanized sheet metal
shield, Cooper B-Line B3100 with B3151 or B3153 series.b. 21/2inch and larger pipes:
i. Adjustable steel yoke pipe roll with pipe covering protectionsaddle, CooperB-Line B3110 with B3160 - B3165 series.
ii. Pipe roll with sockets with pipe covering protection saddle,Cooper B-LineB3114 with B3160 - B3165 series.
4. Insulated pipe - Cold or chilled water piping:a. 5 inch andsmaller pipes: use adjustable steel clevis with galvanized sheetmetal
shield, Cooper B-Line B3100 with B3151 or B3153 series.b. 6 inchand larger pipes:
i. Adjustable steel yoke pipe, Cooper B-Line B3110, with B3380CW- B3384CWcalcium silicate shield.
ii. Pipe roll with sockets, Cooper B-Line B3114, with B3380CW -B3384CW calcium silicate shield.
B. PIPE CLAMPS1. When flexibility in the hanger assembly isrequired due to horizontal movement, use
pipe clamps with weldless eye nuts, Cooper B-Line B3140 or B3142with B3200. Forinsulated lines use double bolted pipe clamps,Cooper B-Line B3144 or B3146 with B3200.
C. MULTIPLE OR TRAPEZE HANGERS1. Trapeze hangers shall beconstructed from 12 gauge roll formed ASTM A 1011 SS Gr. 33
structural steel channel, 15/8 x 15/8 minimum, Cooper B-Line B22strut or stronger asrequired.
2. Mount pipes to trapeze with two piece pipe straps sized foroutside diameter of pipe,Cooper B-Line B2000 series.
3. For pipes subjected to axial movement:a. Strut mounted rollersupport, Cooper B-Line B3126. Use pipe protection shield or
saddles on insulated lines.b. Strut mounted pipe guide, CooperB-Line B2417.
D. WALL SUPPORTS1. Pipes 4 inch and smaller:
a. Carbon steel hook, Cooper B-Line B3191.b. Carbon steelJ-hanger, Cooper B-Line B3690.
2. Pipes larger than 4 inch:a. Welded strut bracket and pipestraps, Cooper B-Line B3064 and B2000 series.b. Welded steelbrackets, Cooper B-Line B3066 or B3067, with roller chair oradjustable
steel yoke pipe roll. Cooper B-Line B3120 or B3110. Use pipeprotection shield orsaddles on insulated lines.
Tech
nica
l Dat
a
Technical Data
19
E. FLOOR SUPPORTS1. Hot piping under 6 inch and all coldpiping:
a. Carbon steel adjustable pipe saddle and nipple attached tosteel base stand sizedfor pipe elevation, Cooper B-Line B3093 andB3088T or B3090 and B3088. Pipe saddleshall be screwed or welded toappropriate base stand.
2. Hot piping 6 inch and larger:a. (Adjustable) Roller standwith base plate, Cooper B-Line B3117SL (or B3118SL).b. Adjustableroller support and steel support sized for elevation, Cooper B-LineB3124
F. VERTICAL SUPPORTS1. Steel riser clamp sized to fit outsidediameter of pipe, Cooper B-Line B3373 or B3374.
G. COPPER TUBING SUPPORTS1. Hangers shall be sized to fit coppertubing outside diameters.
a. Adjustable steel swivel ring (band type) hanger, CooperB-Line B3170CT.b. Malleable iron ring hanger, Cooper B-Line B3198CTor hinged ring hanger B3198HCT.c. Government type hanger, CooperB-Line B3225CT or B3226CT.d. Adjustable steel clevis hanger, CooperB-Line B3104CT.
H. PLASTIC PIPE SUPPORTS1. V-bottom clevis hanger withgalvanized 18 gauge continuous support channel, Cooper
B-Line B3106 and B3106V, to form a continuous support system forplastic pipe or flexibletubing.
I. SUPPLEMENTARY STRUCTURAL SUPPORTS1. Design and fabricatesupports using structural quality steel bolted framingmaterials
as manufactured by Cooper B-Line. Channels shall be roll formed,12 gauge ASTMA 1011 SS Grade 33 steel, 15/8 x 15/8 or greater asrequired by loading conditions.Submit designs for pipe tunnels,pipe galleries, etc., to engineer for approval. Useclamps andfittings designed for use with the strut system.
2.04 UPPER ATTACHMENTS
A. BEAM CLAMPS1. Beam clamps shall be used where piping is to besuspended from building steel.
Clamp type shall be selected on the basis of load to besupported, and load configuration.2. C-Clamps shall have locknutsand cup point set screws, Cooper B-Line B351L, or B3036L.
Top flange C-clamps shall be used when attaching a hanger rod tothe top flange of structural shapes, Cooper B-Line B3034 or B3033.Refer to manufacturersrecommendation for setscrew torque. Retainingstraps shall be used to maintain theclamps position on the beamwhere required.
3. Center loaded beam clamps shall be used where specified.Steel clamps shall be CooperB-Line B3050 or B3055. Malleable ironor forged steel beam clamps with cross bolt shallbe Cooper B-LineB3054 or B3291 - B3297 series as required to fit beams.
B. CONCRETE INSERTS1. Cast in place spot concrete inserts shallbe used where applicable, either steel or
malleable iron body, Cooper B-Line B2500 or B3014. Spot insertsshall allow for lateraladjustment and have means for attachment toforms. Select insert nuts to suit threaded hanger rod sizes, CooperB-Line N2500 or B3014N series.
Technical Data
Technical Data
20
2. Continuous concrete inserts shall be used where applicable.Channels shall be 12gauge, ASTM A 1011 SS Grade 33 structuralquality carbon steel, complete withstyrofoam inserts and end capswith nail holes for attachment to forms. Thecontinuous concreteinsert shall have a load rating of 2,000 lbs/ft. in concrete,Cooper B-Line B22I, B32I, or B52I (B52I is limited to 1,500lbs/ft.). Select channel nutssuitable for strut and rod sizes.
2.05 VIBRATION ISOLATION AND SUPPORTS
A. For refrigeration, air conditioning, hydraulic, pneumatic,and other vibrating systemapplications, use a clamp that has avibration dampening insert and a nylon insertedlocknut. For copperand steel tubing use Cooper B-Line BVT series VibraClamps, forpipesizes use BVP series.
B. For larger tubing or piping subjected to vibration, useneoprene or spring hangers as required.
C. For base mounted equipment use vibration pads, moldedneoprene mounts, or springmounts as required.
D. Vibration isolation products as manufactured by CooperB-Line, VibraTrol systems.
2.06 ACCESSORIES
A. Hanger rods shall be threaded both ends, Cooper B-Line B3205,or continuous threaded rodsof circular cross section. Use adjustinglocknuts at upper attachments and hangers. No wire, chain, orperforated straps are allowed.
B. Shields shall be 180 galvanized sheet metal, 12 inch minimumlength, 18 gauge minimumthickness, designed to match outsidediameter of the insulated pipe, Cooper B-Line B3151.
C. Pipe protection saddles shall be formed from carbon steel,1/8 inch minimum thickness,sized for insulation thickness. Saddlesfor pipe sizes greater than 12 inch shall have a center supportrib.
2.07 FINISHESINDOOR FINISHES
A. Hangers and clamps for support of bare copper piping shall becoated with copper coloredepoxy paint, Cooper B-Line Dura-Copper.Additionally a plastic coating or a felt lining inhanger can beused.
B. Hangers for other than bare copper pipe shall be zinc platedin accordance with ASTMB 633 - SC3 or shall have anelectro-deposited green epoxy finish, Cooper B-Line Dura-Green.
C. Strut channels shall be pre-galvanized in accordance withASTM A 653 G90 or havean electro-deposited green epoxy finish,Cooper B-Line Dura-Green.
OUTDOOR AND CORROSIVE AREA FINISHES
D. Hangers and strut located outdoors shall be hot dipgalvanized after fabrication inaccordance with ASTM A 123. Allhanger hardware shall be hot-dip galvanized orstainless steel. Zincplated hardware is not acceptable for outdoor or corrosive use.
E. Hangers and strut located in corrosive areas shall be Type304 (316) stainless steelwith stainless steel hardware.
Tech
nica
l Dat
a
Technical Data
21
Part III - EXECUTION
3.01 PIPE HANGERS AND SUPPORTS
A. Pipe shall be adequately supported by pipe hanger andsupports specified in PART II -PRODUCTS. Hangers for insulatedpipes shall be sized to accommodate insulationthickness.
B. Horizontal steel piping shall be supported in accordance withMSS SP-69 Tables 3 and 4,excerpts of which follow below:
NOMINAL PIPE SIZE ROD DIAMETER MAXIMUM SPACING
3/8 - 11/4 3/8 7-011/2 3/8 9-0
2 3/8 10-021/2 1/2 11-0
3 1/2 12-031/2 1/2 13-0
4 5/8 14-05 5/8 16-06 3/4 17-08 3/4 19-010 7/8 22-012 7/8 23-0141 25-016 1 27-0
C. Horizontal copper tubing shall be supported in accordancewith MSS SP-69 Tables 3and 4, excerpts of which follow below:
NOMINAL PIPE SIZE ROD DIAMETER MAXIMUM SPACING
1/4 - 3/4 3/8 5-01 3/8 6-0
11/4 3/8 7-011/2 3/8 8-0
2 3/8 8-021/2 1/2 9-0
3 1/2 10-031/2 1/2 11-0
4 1/2 12-05 1/2 13-06 5/8 14-08 3/4 16-0
D. Provide means of preventing dissimilar metal contact such asplastic coated hangers, copper colored Cooper B-Line Dura-Copperepoxy paint, or non-adhesive isolation tape(Cooper B-LineIso-Pipe). Galvanized felt isolators sized for copper tubing mayalso be used,Cooper B-Line B3195CT.
Technical Data
Technical Data
22
E. Support horizontal cast iron pipe adjacent to each hub, with10 feet maximum spacing between hangers.
F. Install hangers to provide a minimum of 1/2 inch spacebetween finished covering andadjacent work.
G. Place a hanger within 12 inches of each horizontal elbow.
H. Support vertical piping independently of connected horizontalpiping. Support verticalpipes at every (other) floor. Whereverpossible, locate riser clamps directly below pipecouplings or shearlugs.
I. Where several pipes can be installed in parallel and at thesame elevation, provide trapezehangers as specified in Section 2.02C. Trapeze hangers shall be spaced according to thesmallest pipesize, or install intermediate supports according to schedule inSection 3.01 B.
J. Do not support piping from other pipes, ductwork or otherequipment which is notbuilding structure.
3.02 CONCRETE INSERTS
A. Provide inserts for placement in formwork before concrete ispoured.
B. Provide inserts for suspending hangers from reinforcedconcrete slabs and sides ofreinforced concrete beams.
C. Where concrete slabs form finished ceilings, provide insertsto be flush with slab surface.
D. Provide hooked rod to concrete reinforcement section forinserts carrying pipe over 4 inch.
Tech
nica
l Dat
a
Technical Data
23
Beam clamps offered in this section are designed to provideattachment of hanger rods to structural members withoutdrilling orwelding. A wide range of types and sizes are available for variousapplications.MaterialsCarbon Steel, Malleable Iron and Forged Steelare used in the manufacturing of beam clamps and accessories.Stainlesssteel and other materials are available.
FinishesThe standard finishes for mechanical supports are plainsteel (oil coated) sometimes referred to as black andElectro-PlatedZinc (ASTM B 633 SC3). Hot-Dip Galvanized AfterFabrication (ASTM A 123), Red Primer, Plastic Coating andDura-Green.Other special coatings are available upon request.Note:Due to the design of some products, (threads, connecting hardware,swivels, etc.) items may or may not be uniformly coated withspecial finishes. In some cases, the hanger itself may be coated,however, thehardware may be supplied Electro-Plated, copper plated,or in stainless steel.Recommended Setscrew Torque (unless otherwisespecified)
1/4-20 3/8-16 1/2-13 5/8-11 3/4-104 ft/lbs (5 Nm) 5 ft/lbs (7Nm) 11 ft/lbs (15 Nm) 21 ft/lbs (28 Nm) 34 ft/lbs (46 Nm)
Over torqued setscrews will damage beam clamps in thissection.We are aware that torque wrenches are not used or notavailable in many instances. In the absence of a torque wrench,thesetscrew should be finger tightened to the I-beam and then anadditional 1/4 to 1/2 turn applied to the setscrew.Approvals (asnoted)Items in this section are Underwriters' Laboratories Listedand comply with Federal Specification WW-H-171E & A-A-1192A orManufacturers Standardization Society MSS SP-69 & SP-58.
Beam
Clam
ps
Beam Clamps
24
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Beam Clamps
Material: Steel (Stainless Steel Type 304 available 3/8" thru5/8" rod sizes)Standard Finish: Plain or Electro-PlatedService:Designed for attaching a hanger rod to the flange of abeam.Ordering: Specify part number and finish. WhenRetaining Strapis required, order B3362 thruB3365 separately. See page26.Approvals: B351L (3/8 - 3/4), is Underwriters'LaboratoriesListed. Complies with FederalSpecification WW-H-171E &A-A-1192A Type 23and Manufacturers Standardization Society MSSSP-69 & SP-58 Type 23.
Part Rod Design MaximumNo. Size Load Iron Pipe Size Wt./C
'A' 'B' 'C' 'D' Lbs. kN Per UL Lbs. kg
B351L-3/8 3/8"-16 23/8" (60.3) 23/8" (60.3) 3/4" (19.0) 300(0.89) 4" (100) 41 (18.6)B351L-1/2 1/2"-13 23/8" (60.3) 23/8"(60.3) 3/4" (19.0) 380 (1.69) 4" (100) 41 (18.6)B351L-5/8 5/8"-1123/8" (60.3) 21/4" (57.1) 3/4" (19.0) 550 (2.44) 6" (150) 60(27.2)B351L-3/4 3/4"-10 23/8" (60.3) 21/4" (57.1) 3/4" (19.0) 630(2.80) 6" (150) 71 (32.2)B351L-7/8 7/8"-9 3" (76.2) 31/4" (82.5) 1"(25.4) 1200 (5.34) -- -- 184 (83.4)
Figure B351L Steel C-Clamp With Locknut
Figure B3036L Malleable Iron C-Clamp With Locknut
Note: See page 24 for recommended setscrew torque.
Note: See page 24 for recommended setscrew torque.
Material: Malleable Iron
Standard Finish: Plain or Electro-Plated
Service: Designed for attaching a hanger rod tothe flange of abeam.Ordering: Specify part number and finish.When Retaining Strapis required, order B3362 thruB3365 separately. See page26.Approvals: B3036L is Underwriters' LaboratoriesListed. Complieswith Federal SpecificationWW-H-171E & A-A-1192A Type 23andManufacturers Standardization Society MSS SP-69& SP-58 Type23.
Setscrew andLocknut Included
Setscrew andLocknut Included
'A'(Rod Size)
Hanger RodNot Included
'A'(Rod Size)
Hanger RodNot Included
'B'
3/4"(19.0)
'C'
'B'
'C'
'D'
Bea
m C
lam
ps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Part Rod Design MaximumNo. Size Load Iron Pipe Size Wt./C
'A' 'B' 'C' Lbs. kN Per UL Lbs. kg
B3036L-3/8 3/8"-16 13/4" (44.4) 13/4" (44.4) 300 (0.89) 4" (100)41 (18.6)B3036L-1/2 1/2"-13 13/4" (44.4) 13/4" (44.4) 380 (1.69) 5"(125) 41 (18.6)B3036L-5/8 5/8"-11 2" (50.8) 17/8" (47.6) 530 (2.36)6" (150) 60 (27.2)B3036L-3/4 3/4"-10 2" (50.8) 2" (50.8) 530 (2.36)6" (150) 71 (32.2)
25
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Beam Clamps
Material: Steel (Stainless Steel available)Standard Finish:Pre-GalvanizedService: Designed for use with B351L andB3036LC-Clamps.Ordering: Specify part number, length 'L', (add1"(25.4) minimum to flange width), and finish.
Note: Requires field forming on beam.
Material: Malleable IronStandard Finish: Plain orElectro-Plated
Service: Designed for attaching a 3/8"-16 hanger rod to the topor bottom flange of a beam or bar joist whensetscrew is in the downposition as shown.Ordering: Specify part number and finish.WhenRetaining Strap is required, order B3367 separately.See Page30.Approvals: Underwriters' Laboratories Listed.Complies withFederal Specification WW-H-171E &A-A-1192A Type 19 andManufacturers StandardizationSociety MSS SP-69 & SP-58 Type19.Weight: Wt./C 25 Lbs. (11.3 kg)Design Load: 350 Lbs. (1.55kN)
Material: Malleable Iron
Standard Finish: Plain or Electro-Plated
Service: Designed for attaching a 3/8"-16 hanger rod to thebottom flange of a Z-purlin.Ordering: Specify part number andfinish. Weight: Wt./C 90 Lbs. (40.8 kg)Design Load: 400 Lbs. (1.78kN)Approvals: Underwriters' Laboratories Listed.Complies withFederal Specification WW-H-171E &A-A-1192A Type 23 andManufacturers StandardizationSociety MSS SP-69 & SP-58 Type23.
Figure B3362, B3363, B3364, B3365 Retaining Strap
Figure B3031-3/8 Light DutyMalleable C-ClampNote: See page 24for recommended setscrew torque.
Figure B3037 Z-Purlin Malleable C-ClampNote: See page 24 forrecommended setscrew torque.
Material Thickness12 Gauge (2.7)
Hanger RodNot Included
Setscrew andLocknut Included
Throat Opening11/16" (17.5)
'B' 3/4"(19.0)
3/4"(19.0)
11/2"(38.1)
17/8"(47.6)
Wt./C for Length 'L' ofPart 6" (152.4) 8" (203.2) 10" (254.0)12" (304.8)No. For Use With 'A' 'B' Lbs. kg Lbs. kg Lbs. kg Lbs.kg
B3362 B351L-3/8 & 1/2 11/4" (31.7) 7/16" (11.1) 27 (12.2) 35(15.9) 44 (19.9) 52 (23.6)B3363 B351L-5/8 & 3/4, 11/4" (31.7)5/8" (15.9) 26 (11.8) 35 (15.9) 43 (19.5) 52 (23.6)
B3036L-3/8 & 1/2B3364 B3036L-5/8 & 3/4 11/4" (31.7)11/16" (17.4) 26 (11.8) 35 (15.9) 43 (19.5) 52 (23.6)B3365B351L-7/8 11/2" (38.1) 3/4" (19.0) 32 (14.5) 42 (19.0) 52 (23.6) 62(28.1)
Setscrew andLocknut Included3"
(76.2)
313/32"(86.5)
Throat Opening31/32" (24.6)
Bottom HangerRod Threads
3/8"-16
'L'
'A'
Beam
Clam
ps
26
Beam Clamps
Figure B3033 Wide Jaw Reversible C-Clamp
Note: See page 24 for recommended setscrew torque.
Material: Ductile IronStandard Finish: Plain or Electro-Platedscrewwith Hot-Dipped Galvanized clampService: Designed forattaching a hanger rod tothe top or bottom flange of a bar joist orotherstructural shapes.Note: Installation of C-Clamp other thanshownbelow is not recommended.Ordering: Specify part number andfinish.When Retaining Strap is required, order B3367separately. Seepage 30.Approvals: Underwriters' Laboratories Listed.Complies withFederal Specification WW-H-171EType 19 & A-A-1192A Type 19& 23 andManufacturers Standardization SocietyMSS SP-69 &SP-58 Type 19 & 23.
Part Rod Design MaximumNo. Size Load Iron Pipe Size Wt./C
'A' 'B' 'C' 'D' Lbs. kN Per UL Lbs. kg
B3033-3/8 3/8"-16 21/4" (57.1) 2" (50.8) 11/8" (28.6) 500 (2.22)4" (100) 54 (24.5)B3033-1/2 1/2"-13 25/16" (58.7) 23/16" (55.6)11/4" (31.7) 810 (3.60) 8" (200) 51 (23.1)B3033-5/8 5/8"-11 25/8"(66.7) 21/2" (63.5) 13/8" (34.9) 1000 (4.44) 8" (200) 70(31.7)B3033-3/4 3/4"-10 211/16" (68.3) 21/2" (63.5) 17/16" (36.5)1400 (6.23) 10" (250) 98 (44.4)
Setscrew andLocknut Included
Top FlangeAttachmentApplications
Bottom FlangeAttachmentApplications
'A'(Rod Size)
Hanger RodNot Included
'B'
'D''C'
Throat Opening11/4" (31.7) for B3033-3/8 & 1/215/16" (83.3)for B3033-5/8 & 3/4
Bea
m C
lam
ps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
27
Figure B3034 C-Clamp
Note: See page 24 for recommended setscrew torque.
Material: Ductile Iron for 3/8 & 1/2 sizesMalleable Iron for5/8 & 3/4 sizes
Standard Finish: Plain or Electro-Plated screwwith Hot-DippedGalvanized clampService: Designed for attaching a hanger rod tothetop or bottom flange (for their respective sizes)of a bar joist orother structural shapes.Note: Installation of C-Clamps (for theirrespectivesizes) other than shown is not recommended.Ordering:Specify part number and finish.When Retaining Strap is required,order B3367separately. See page 30.Approvals: Underwriters'Laboratories Listed(3/8 and 1/2only). Complies withFederalSpecification WW-H-171E Type 19 & A-A-1192AType 19 &23 and Manufacturers StandardizationSociety MSS SP-69 & SP-58Type 19 & 23.
Setscrew andLocknut Included
'A'(Rod Size)
Hanger RodNot Included
'B'
'D''C'
ThroatOpening3/4" (19.0)
B3034-5/8" and B3034-3/4" sizesAttach only as shown.
Part Rod Design MaximumNo. Size Load Iron Pipe Size Wt./C
'A' 'B' 'C' 'D' Lbs. kN Per UL Lbs. kg
B3034-3/8 3/8"-16 15/8" (41.3) 2" (50.8) 7/8" (19.0) 560 (2.49)4" (100) 30 (13.6)B3034-1/2 1/2"-13 113/16" (46.0) 23/16" (55.6)13/16" (30.2) 810 (3.60) 8" (200) 47 (21.3)B3034-5/8 5/8"-11 13/4"(44.5) 21/8" (54.0) 11/4" (31.7) 1000 (4.45) -- -- 58(26.3)B3034-3/4 3/4"-10 2" (50.8) 21/4" (57.2) 11/4" (31.7) 1500(6.67) -- -- 77 (35.0)
Top FlangeAttachmentApplications
Bottom FlangeAttachmentApplications
Setscrew andLocknut Included
'A'(Rod Size)
Hanger RodNot Included
'B'
'D''C'
ThroatOpening3/4" (19.0)
B3034-3/8" and B3034-1/2" sizesAttach only as shown.
Beam
Clam
ps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Beam Clamps
28
Material: SteelStandard Finish: Electro-Plated or Hot-DipGalvanizedService: Designed for attaching a hanger rod to theflange of a beam.Ordering: Specify part number and finish.WhenRetaining Strap is required, order B312 separately.See page30.Recommended Setscrew Torque: 1/2-13 = 350 in-lbs (39.5 Nm)5/8-11= 700 in-lbs (79.0 Nm)Minimum Flange Thickness: For B321-1 thruB321-3 = 3/8 (9.5) For B321-4 & B321-5 = 5/8 (15.9)Approvals:Complies with Federal SpecificationWW-H-171E & A-A-1192A Type19 and ManufacturersStandardization Society MSS SP-69 & SP-58Type 19.
Material: SteelStandard Finish: Electro-Plated or Hot-DipGalvanizedService: Designed for attaching a hanger rod to theflange of a beam.Ordering: Specify part number and finish.WhenRetaining Strap is required, order B312 separately.See page30.Recommended Setscrew Torque: 3/8-16 = 150 in-lbs (16.9 Nm)1/2-13= 350 in-lbs (39.5 Nm)Approvals: Complies with FederalSpecificationWW-H-171E & A-A-1192A Type 19 andManufacturersStandardization Society MSS SP-69 & SP-58 Type19.
Part Rod Setscrew Design Load Wt./CNo. Size A Size 'C' 'T' Lbs.kN Lbs. kg
B303 1/4-20 3/8-16 25/16" (58.7) 11 Ga. (3.0) 400 (1.78) 72(32.6)B304 5/16-18 3/8-16 25/16" (58.7) 11 Ga. (3.0) 600 (2.67) 72(32.6)B305 3/8-16 3/8-16 25/16" (58.7) 11 Ga. (3.0) 600 (2.67) 72(32.6)B306 3/8-16 1/2-13 27/16" (61.9) 7 Ga. (4.5) 1100 (4.89) 97(44.0)B307 1/2-13 1/2-13 27/16" (61.9) 7 Ga. (4.5) 1100 (4.89) 97(44.0)B308 1/2-13 1/2-13 29/16" (65.1) 1/4" (6.3) 1500 (6.67) 133(60.3)B309 5/8-11 1/2-13 29/16" (65.1) 1/4" (6.3) 1500 (6.67) 133(60.3)
Figure B303-B309 Beam Clamps
Figure B321 Series Beam Clamps
Part Rod Setscrew Design Load Wt./CNo. Size A Size 'C' 'T' Lbs.kN Lbs. kg
B321-1 3/8-16 1/2-13 39/16" (92.1) 1/4" (6.3) 1300 (5.78) 187(84.8)B321-2 1/2-13 1/2-13 39/16" (92.1) 1/4" (6.3) 1400 (6.23) 186(84.3)B321-3 5/8-11 1/2-13 39/16" (92.1) 1/4" (6.3) 1600 (7.12) 185(83.9)B321-4 5/8-11 5/8-11 323/32" (94.4) 5/16" (7.9) 1800 (8.00)239 (108.4)B321-5 3/4-10 5/8-11 323/32" (94.4) 5/16" (7.9) 2000(8.89) 238 (107.9)
SetscrewIncluded
'C'
'T'
'A'
111/16" (42.8)Maximum
FlangeThickness
15/8"(41.3)
31/4"(82.5)
'C'
'T'
'A'
7/8" (22.2)Maximum
FlangeThickness
11/8"(28.6)
21/2"(63.5)
SetscrewIncluded
Bea
m C
lam
ps
Beam Clamps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
29
Material: SteelStandard Finish: Plain or Electro-PlatedService:Designed for attaching rod under a beamflange. Adjustable for 4"(101.6) to 8" (203.2) flangewidths. Maximum flange thickness 3/4"(19.0).Ordering: Specify part number and finish. Approvals:Complies with Federal SpecificationWW-H-171E Type 54 &A-A-1192A Type 27 andManufacturers Standardization Society MSSSP-69& SP-58 Type 27.
Figure B3040 Adjustable Beam ClampPart Rod Size Design LoadWt./CNo. 'A' 'B' 'C' Steel Size Lbs. kN Lbs. kg
B3040-3/8 3/8"-16 23/4" (69.8) 113/16" (46.0) 1/4" x 11/4" (6.3x 31.7) 300 (1.33) 120 (54.4)B3040-1/2 1/2"-13 23/4" (69.8) 13/4"(44.4) 1/4" x 11/2" (6.3 x 38.1) 700 (3.11) 160 (72.6)B3040-5/85/8"-11 3" (76.2) 13/4" (44.4) 1/4" x 13/4" (6.3 x 44.4) 1000(4.45) 216 (98.0)B3040-3/4 3/4"-10 33/8" (85.7) 17/8" (47.6) 3/8" x21/2" (9.5 x 63.5) 1800 (8.00) 442 (200.5)
J-Hook and HexNut Included
'A'(Rod Size)
Hanger RodNot Included
'C'Center of J-Hook to
bottom of clamp body.'B'
Steel Size'C'
'A'
Material: SteelStandard Finish: Pre-GalvanizedService: Designedfor use with B3031, B3033, andB3034 C-Clamps.Ordering: Specify partnumber, length 'L', (add 2"(50.8) minimum to flange width), andfinish.
Wt./C for Length 'L' ofPart 6" (152.4) 8" (203.2) 10" (254.0)12" (304.8)No. For Use With 'A' 'B' Lbs. kg Lbs. kg Lbs. kg Lbs.kg
B3367-3/8 B3033-3/8, B3034-3/8 & B3031-3/8 11/4" (31.7)7/16" (11.1) 26 (11.8) 35 (15.9) 44 (19.9) 61 (27.6)B3367-1/2B3033-1/2 & B3034-1/2 11/4" (31.7) 9/16" (14.3) 25 (11.3) 34(15.4) 43 (19.5) 60 (27.2)B3367-5/8 B3033-5/8 & B3034-5/8 11/4"(31.7) 11/16" (17.5) 24 (10.9) 33 (14.9) 42 (19.0) 59(26.7)B3367-3/4 B3033-3/4 & B3034-3/4 11/4" (31.7) 13/16"(20.6) 23 (10.4) 32 (14.5) 41 (18.6) 58 (26.3)
Figure B3367 Retaining Straps
Material Thickness11 Gauge (3.0)
'B' Dia.
'L'
'A'
Material: SteelStandard Finish: Pre-GalvanizedService: Designedfor use with B303-B309 andB321 beam clamps.Ordering: Specify partnumber and finish.
Notes:Maximum beam thickness 3/4 (19.0).For thicker beams stepup one flange widthsize.Requires field forming on beam.
Part Wt./CNo. For Flange With 'L' Lbs. kg
B312-6 6" (152.4) 9" (228.6) 22 (10.0)B312-9 9" (228.6) 12"(304.8) 30 (13.6)B312-12 12" (304.8) 15" (381.0) 40 (18.1)B312-1515" (381.0) 18" (457.2) 49 (22.2)
Figure B312 Retaining Straps
Material Thickness14 Gauge (1.9)
'L'
1/4"(6.3)
1/2"(12.7)1
1/4"(31.7)
13/4"(44.4)
Note:Requiresfield formingon beam.
Beam
Clam
ps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Beam Clamps
30
Material: SteelStandard Finish: Plain or Electro-Plated
Service: Designed for attaching a hanger rod to becentered underbeam flanges. 2" (50.8) verticaladjustment is provided in theclamp.Ordering: Specify part number, flange width, andfinish.
Approvals: Complies with Federal SpecificationWW-H-171E &A-A-1192A Type 21 andManufacturers Standardization Society MSSSP-69 &SP-58 Type 21.
Figure B3055 Steel Beam Clamp
Note:Box Style
Furnished ForB3055-3/8 x 2"B3055-3/8 x 3"B3055-3/8 x 4"B3055-1/2x 2"B3055-1/2 x 3"B3055-1/2 x 4"B3055-5/8 x 2"B3055-5/8 x3"B3055-5/8 x 4"B3055-3/4 x 2"B3055-3/4 x 3"B3055-3/4 x 4"B3055-7/8x 3"B3055-7/8 x 4"B3055-7/8 x 5"B3055-1 x 3"B3055-1 x 4"B3055-1 x5"B3055-1 x 6"B3055-11/8 x 4"B3055-11/8 x 5"B3055-11/8 x6"B3055-11/8 x 7"B3055-11/4 x 4"B3055-11/4 x 5"B3055-11/4 x6"B3055-11/4 x 7"
Bolt and NutIncluded
Steel Size
Steel Size
'B'Center of cross boltto bottom of side of
hanger rod nut.
NOTE:Slots on bottom
portions of clamphalves allow 1 (25.4)
adjustment for variance in flange
widths'A'
(Rod Size)Hanger RodNot Included
'A'(Rod Size)
Hanger RodNot Included
'B'
'B'
'W'
'W''C'
'C'
Rod Size Design LoadPart No. 'A' 'B' 'C' Steel Size Lbs. kN
B3055-3/8 3/8"-16 3" (76.2) 4" (101.6) 1/4" x 11/4" (6.3 x 31.7)550 (2.44)B3055-1/2 1/2"-13 3" (76.2) 4" (101.6) 1/4" x 11/2" (6.3x 38.1) 850 (3.78)B3055-5/8 5/8"-11 31/4" (82.5) 41/2" (114.3) 3/8"x 11/2" (9.5 x 38.1) 1100 (4.89)B3055-3/4 3/4"-10 31/4" (82.5)41/2" (114.3) 3/8" x 2" (9.5 x 50.8) 1500 (6.67)B3055-7/8 7/8"-931/2" (88.9) 5" (127.0) 1/2" x 2" (12.7 x 50.8) 2600 (11.56)B3055-11"-8 31/2" (88.9) 51/2" (139.7) 1/2" x 21/2" (12.7 x 63.5) 4300(19.12)
Flange Approximate Wt./C For Beam Clamp Size Lbs. (kg)
Width 'W' B3055-3/8" B3055-1/2" B3055-5/8" B3055-3/3" B3055-7/8"B3055-1"
4" (101.6) 168 (76.2) 201 (91.2) 328 (148.8) 434 (196.8) 657(298.0) 797 (361.5)5" (127.0) 181 (82.1) 217 (98.4) 352 (159.6) 466(211.4) 667 (302.5) 824 (373.7)6" (152.4) 193 (87.5) 231 (104.8)373 (169.2) 495 (224.5) 705 (319.8) 877 (397.8)7" (177.8) 205(93.0) 246 (111.6) 395 (179.2) 525 (238.1) 744 (337.5) 926(420.0)8" (203.2) 214 (97.1) 256 (116.1) 411 (186.4) 546 (247.6)773 (350.6) 962 (436.3)10" (254.0) 235 (106.6) 282 (127.9) 449(203.6) 596 (270.3) 840 (381.0) 1046 (474.4)12" (304.8) 259 (117.5)311 (141.0) 493 (223.6) 655 (297.1) 918 (416.4) 1143 (518.4)
Bea
m C
lam
ps
Beam Clamps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
31
Material: SteelStandard Finish: Plain or Electro-PlatedService:Designed for attaching hanger rodscentered under beam flanges.Recommended touse with B3200 Series up to size 11/2"(38.1).Ordering: Specify part number, flange width,andfinish.Approvals: Complies with Federal SpecificationWW-H-171E& A-A-1192A Type 21 andManufacturers Standardization SocietyMSS SP-69 & SP-58 Type 21.
Part NumberExample: B3050-2 x 'W' finish
Figure B3050 Beam Clamp
Bolt and Nut Included'B'
'W'
'C'
'A'
Steel Size
Bolt Size
'A'Center of bolt to bottom of
beam flange.
Part No. Bolt 'B' Design Load& Size Size 'A' Minimum 'C'Steel Size Lbs. kN
B3050-2 1/2"-13 13/8" (34.9) 5/8" (15.9) 21/8" (54.0) 1/4"x11/4" (6.3 x 31.7) 1000 (3.11)B3050-5 3/4"-10 17/8" (47.6) 7/8"(22.2) 3" (76.2) 1/2"x 2" (12.7 x 50.8) 3000 (6.67)
Flange Width Flange Thickness Wt./C For Beam Clamp Size'W'
Min. Max. 2 5lbs. kg lbs. kg
4" (101.6) 3/16" (4.8) 1/2" (12.7) 116 (52.6) 429 (194.6)5"(127.0) 5/16" (7.9) 5/8" (15.9) 125 (56.7) 458 (207.8)6" (152.4)1/4" (6.3) 3/4" (19.0) 134 (60.8) 486 (220.5)7" (177.8) 7/16"(11.1) 7/8" (22.2) 143 (64.9) 514 (233.2)8" (203.2) 7/16" (11.1)7/8" (22.2) 152 (69.0) 543 (246.3)9" (228.6) 9/16" (14.3) 1" (25.4)160 (72.6) 571 (259.0)10" (254.0) 5/8" (15.9) 1" (25.4) 169 (76.7)599 (271.8)12" (304.8) 5/8" (15.9) 11/4" (31.7) 187 (84.8) 656(297.6)
Beam
Clam
ps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Beam Clamps
32
Material: Malleable Iron
Standard Finish: Plain or Electro-Plated
Service: Designed for attaching a hanger rod to the bottomflange of a beam. Adjustable for flangewidths of 3" (76.2) to 7"(177.8) and a flange thickness of no greater than 5/8"(15.9).Ordering: Specify part number and finishApprovals:Underwriters' Laboratories Listed.Complies with FederalSpecification WW-H-171E & A-A-1192A Type 30 and ManufacturersStandardizationSociety MSS SP-69 & SP-58 Type 30.
Figure B3054 Malleable Iron Beam Clamp(Available withoutextension piece as B3054).
'E'Rod Take-Out
Clamping Rod andNuts Included
'A'(Rod Size)
Hanger RodNot Included
'E'
Design Load Maximum Iron Pipe Size Wt./CPart No. Lbs. kN Per ULLbs. kg
B3054-3/8 730 (3.25) 4 (100) 236 (107.0)B3054-1/2 1350 (6.00) 8(200) 254 (115.2)B3054-5/8 1365 (6.07) 10 (250) 260(117.9)B3054-3/4 1365 (6.07) 10 (250) 278 (126.1)B3054-7/8 1365(6.07) 10 (250) 292 (132.4)
'A'Rod Rod Take Out 'E' For Beam Flange Width Of
Part No. Size 3" (76.2) 4" (101.6) 5" (127.0) 6" (152.4) 7"(177.8)
B3054-3/8 3/8"-16 411/16" (119.1) 49/16" (115.9) 45/8" (117.5)4" (101.6) 31/8" (79.4)B3054-1/2 1/2"-13 413/16" (122.2) 41/2"(114.3) 45/16" (109.5) 315/16" (100.0) 31/4" (82.5)B3054-5/85/8"-11 47/8" (123.8) 45/8" (117.5) 43/8" (111.1) 33/4" (95.2)35/16" (84.1)B3054-3/4 3/4"-10 51/8" (130.2) 5" (127.0) 45/8"(117.5) 41/4" (107.9) 33/4" (95.2)B3054-7/8 7/8"-9 53/16" (131.8)47/8" (123.8) 411/16" (119.1) 45/16" (109.5) 33/4" (95.2)
Bea
m C
lam
ps
Beam Clamps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
33
To determine (mm) in the above chart, multiply inches by 25.4.*Rod Size required to finish part number (see Rod Size 'A' in topchart). These part numbers are furnished with links.
'C'
'E'
'B'
'A'
Figure B3291, B3292, B3293, B3294, B3295, B3296, B3297, B3298UFS Beam Clamp With Weldless Eye Nut
Available with left hand threads by adding an L to part numberExample: B3291L-*
MaximumBeam Flange Rod Size 'A'
Part No. Thickness (Specify) Design Load Wt./C*Rod Size In. mm *'B' 'C' Lbs. kN Lbs. kg
B3291-* .60 (15.2) 3/8"-16, 1/2"-13, 11/4" (31.7) 11/8" (28.6)3230 (14.36) 390 (176.9)5/8"-11, 3/4"-10B3292-* .60 (15.2) 7/8"-9,1"-8 111/16" (42.9) 11/8" (28.6) 5900 (26.24) 915 (415.0)B3293-*.60 (15.2) 3/8"-16, 1/2"-13, 5/8"-11, 111/16" (42.9) 11/8" (28.6)5900 (26.24) 1300 (589.6)
3/4"-10, 7/8"-9, 1"-8B3294-* 1.031 (26.2) 7/8"-9, 1"-8 11/2"(38.1) 11/8" (28.6) 5900 (26.24) 2165 (982.0)B3295-* 1.031 (26.2)7/8"-9, 1"-8 11/2" (38.1) 11/8" (28.6) 5900 (26.24) 3385(1535.4)B3296-* 1.031 (26.2) 1"-8, 11/8"-7, 21/8" (54.0) 11/8"(28.6) 11500 (51.15) 2390 (1084.1)
11/4"-7, 11/2"-6B3297-* 1.031 (26.2) 11/8"-7, 11/4"-7, 11/2"-621/8" (54.0) 11/8" (28.6) 11500 (51.15) 3575 (1621.6)B3298-* 1.031(26.2) 13/4"-5, 2"-41/2 49/16" (115.9) 11/8" (28.6) 11500 (51.15)3675 (1666.9)
'E' Rod Take-Out For Flange Width
Part No. 3" 4" 5" 6" 7" 8" 9" 10" 11" 12" 13" 14" 15"
B3291-* 41/2" 55/16" 41/16" 35/8" 27/8" -- -- -- -- -- -- ----B3292-* -- 43/4" 47/16" 41/16" 33/8" -- -- -- -- -- -- ----B3293-* -- -- -- -- 515/16" 6" 55/16" 5" -- -- -- -- --B3294-* --613/16" 65/8" 63/8" 57/8" 57/8" 53/8" 413/16" -- -- -- -- --B3295-*-- -- -- -- -- -- -- -- 81/8" 73/4" 71/8" 65/8" 61/16"B3296-* --73/16" 7" 63/4" 61/4" 65/16" 513/16" 53/16" -- -- -- -- --B3297-*-- -- -- -- -- -- -- -- 81/2" 81/8" 71/2" 7" 67/16"B3298-* -- 83/8"87/16" 83/16" 73/4" 73/4" 71/4" 65/8" -- -- -- -- --
With Links
'C'
'E'
'B'
'A'
Material: Forged SteelStandard Finish: Plain orElectro-Plated
Service: Designed for attaching a hanger rod tothe bottom flangeof a beam. Adjustable fromflange widths of 3" (76.2) to 15" (381.0). and flangethickness of no greater than 11/32" (26.2).Ordering:Specify part number, rod size andfinish.
Approvals: Complies with Federal SpecificationWW-H-171E &A-A-1192A (Type 28 without links;Type 29 with links,) and MSS SP-69& SP-58(Type 28 without links; Type 29 with links).
Note: Design load for B3291 thru B3295 basedon maximum rod sizeshown. Use the appropriateall threaded rod design load shown onpage 242for sizes less than maximum.
Beam
Clam
ps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Beam Clamps
34
WithoutLinks
Material: SteelStandard Finish: Plain or Electro Plated
Service: Designed for attaching hanger rod to thetop flange of abeam.Ordering: Specify part number flange width, flangethicknessand finish.
Figure B3042 Top Beam Hook
Figure B3045 Side Beam Clamp
Material: SteelStandard Finish: Plain or Electro PlatedService:Designed for attaching hanger rod to the sideof a beam flange.Works on top or bottom of beam.Ordering: Specify part number,flange width, and finish.Approvals: Complies with FederalSpecificationWW-H-171E & A-A-1192A Type 53 andManufacturersStandardization Society MSS SP-69 & SP-58 Type25.
'A'(Rod Size)
Hanger RodNot Included
'A' (Rod Size)Hanger Rod Not Included
Allows 1/8" (3.2) clearancebetween hanger rod and
flange of beam.
Allows 1/8" (3.2) clearancebetween hanger rod and
flange of beam.
Steel Size
Steel Size
Bolt and Nut Included
'B'
'A'
'W'
'W'
For Nominal Design LoadPart No. 'A' Pipe Size Lbs. kN
B3042-3/8 3/8"-16 3/4-2 (20-50) 300 (1.33)B3042-1/2 1/2"-1321/2-31/2 (65-90) 500 (2.22)
Approximate Wt./C Lbs. (kg)For Width of Beam Flange 'W'
Part No. 4" (101.6) 6" (152.4) 8" (203.2) 12" (304.8)
B3042-3/8 47 (21.3) 62 (28.1) 72 (32.6) 108 (49.0)B3042-1/2 65(29.5) 86 (39.0) 105 (47.6) 146 (66.2)
Flange Flange Thickness Wt./C For Side Beam Clamp Size Lbs.(kg)Width 'W' Minimum Maximum B3045-3/8 B3045-1/2 B3045-5/8B3045-3/4 B3045-7/8
3" (76.2) 1/4" (6.3) 3/8" (9.5) 92 (41.7) 125 (56.7) 245 (111.1)322 (146.0) 576 (261.3)4" (101.6) 3/16" (4.8) 1/2" (12.7) 100(45.3) 141 (63.9) 267 (121.1) 353 (160.1) 618 (280.3)5" (127.0)5/16" (7.9) 5/8" (15.9) 110 (49.9) 152 (68.9) 289 (131.1) 385(174.6) 675 (306.2)6" (152.4) 1/4" (6.3) 3/4" (19.0) 119 (54.0) 164(74.4) 309 (140.1) 412 (186.9) 718 (325.7)7" (177.8) 7/16" (11.1)7/8" (22.2) 128 (58.0) 175 (79.4) 327 (148.3) 443 (200.9) 742(336.6)8" (203.2) 7/16" (11.1) 7/8" (22.2) 134 (60.8) 182 (82.5)345 (156.5) 462 (209.5) 798 (362.0)9" (228.6) 9/16" (14.3) 1"(25.4) 143 (64.8) 198 (89.8) 368 (166.9) 491 (222.7) 848(384.6)
For Nominal Design LoadPart No. 'A' Pipe Size 'B' Steel SizeLbs. kN
B3045-3/8 3/8"-16 3/4-2 (20-50) 31/8" (79.4) 3/16" x 11/4" (4.8x 31.7) 300 (1.33)B3045-1/2 1/2"-13 21/2-31/2 (65-90) 31/8" (79.4)1/4" x 11/4" (6.3 x 31.7) 500 (2.22)B3045-5/8 5/8"-11 4-5 (100-125)31/8" (79.4) 3/8" x 11/2" (9.5 x 38.1) 700 (3.11)
Bea
m C
lam
ps
Beam Clamps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
35
Material: SteelStandard Finish: Electro-Plated orHot-DipGalvanizedService: Designed for attachment to trus joist beams. Usewith B3210 Series eye rods.Ordering: Specify part number andfinish.
Figure B3052 Trus Joist Beam Clamp
HardwareIncluded
3/4"(19.0)3/8"
(9.5)
1/2"(12.7)
2"(50.8)
C
B
A
Material Thickness11 Gauge (3.0)
Part Hardware Design Load Wt./CNo. Size A 'B' 'C' Lbs. kN Lbs.kg
B3052-1 3/8-16 39/16" (90.5) 19/16" (39.7) 19/16" (39.7) 250(1.11) 68 (30.8)B3052-2 3/8-16 39/16" (90.5) 19/16" (39.7) 113/16"(46.0) 250 (1.11) 72 (32.6)B3052-3 3/8-16 39/16" (90.5) 19/16"(39.7) 23/8" (60.3) 250 (1.11) 80 (36.3)B3052-4 3/8-16 39/16"(90.5) 19/16" (39.7) 219/32" (65.9) 250 (1.11) 83 (37.6)B3052-51/2-13 39/16" (90.5) 19/16" (39.7) 39/16" (90.5) 250 (1.11) 105(47.6)B3052-6 1/2-13 313/16" (96.8) 113/16" (46.0) 23/8" (60.3) 250(1.11) 92 (41.7)B3052-7 1/2-13 313/16" (92.1) 113/16" (46.0) 39/16"(90.5) 250 (1.11) 108 (49.0)B3052-8 1/2-13 39/16" (92.1) 19/16"(39.7) 413/16" (122.2) 250 (1.11) 120 (54.4)B3052-9 1/2-13 39/16"(92.1) 19/16" (39.7) 59/16" (141.3) 250 (1.11) 130 (58.9)
Beam
Clam
ps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Beam Clamps
36
Bea
m C
lam
ps
Beam Clamps
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
37
Pip
e H
angers
Pipe hangers offered in this section are designed to supportinsulated or non-insulated pipe allowing for verticaladjustment andlimited movement in the piping system.
MaterialsCarbon Steel, Malleable Iron and AISI Type 304 &316 Stainless Steel are used in the manufacturing of pipehangers.Other materials are available.
FinishesThe standard finishes for mechanical supports are plainsteel (oil coated) sometimes referred to as black,Electro-PlatedZinc (ASTM B 633 SC3), Pre-Galvanized (ASTM A 653 G90), Hot-DipGalvanized After Fabrication(ASTM A123), Red Primer, PlasticCoating, Dura-Green, Dura-Copper and other special coatings areavailableupon request.
Note: Due to the design of some products, (threads, connectinghardware, swivels, etc.) items may or may notbe uniformly coatedwith special finishes i.e. Hot-Dip Galvanized, Dura Green, DuraCopper, PVC etc. In somecases, the hanger itself may be coated,however, the hardware may be supplied Electro-Plated, DuraCopperPainted or Stainless Steel. Consult B-Line Systems foravailability.
Approvals (as noted)Items in this section are UnderwritersLaboratories Listed, comply with Federal Specification WW-H-171E& A-A-1192A or Manufacturers' Standardization Society MSS SP-69& SP-58.
Pipe Hangers
38
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Material: SteelStandard Finish: Electro-Plated(Hot-DipGalvanized available with Electro-Platedhardware)Service:Designed for suspending insulatedpipe (with shield) andnon-insulated pipeallowing for vertical adjustment. Sideholepermits wall mounting.Ordering: Specify part number andfinish.Approvals: Complies with Federal SpecificationA-A-1192A Type5 and ManufacturersStandardization Society MSS SP-69 &SP-58Type 5.
Figure B3690 Adjustable "J" Hanger(Available with plasticcoating as B3690C-size or felt lined as B3690F-Size)
'B'
'D'
'C''A' (Rod Size)
Hanger Rod NotIncluded
'B'Center of pipe to top
of hanger.
'D'Rod Take-Out
Center of pipe to bottom of hanger rod.
Bolt Size
'E' Dia.
Bolt and Nut Included
Nominal Rod Size Rod Take Out Dia.Part No. Pipe Size 'A' 'B' 'C''D' 'E'
B3690-1/2 1/2" (15) 3/8"-16 23/32" (53.2) 1" (25.4) 111/16"(42.5) 13/32" (10.3)B3690-3/4 3/4" (20) 3/8"-16 211/32" (59.5) 1"(25.4) 113/16" (46.2) 13/32" (10.3)B3690-1 1" (25) 3/8"-16 219/32"(65.9) 1" (25.4) 115/16" (49.2) 13/32" (10.3)B3690-11/4 11/4" (32)3/8"-16 213/16" (71.4) 1" (25.4) 2" (50.8) 13/32" (10.3)B3690-11/211/2" (40) 3/8"-16 31/16" (77.8) 1" (25.4) 21/8" (53.7) 13/32"(10.3)B3690-2 2" (50) 3/8"-16 31/2" (88.9) 1" (25.4) 25/16" (58.7)13/32" (10.3)B3690-21/2 21/2" (65) 1/2"-13 47/16" (112.7) 1" (25.4)3" (76.2) 9/16" (14.3)B3690-3 3" (80) 1/2"-13 47/8" (123.8) 1"(25.4) 31/8" (79.4) 9/16" (14.3)B3690-31/2 31/2" (90) 1/2"-1353/16" (131.8) 1" (25.4) 33/16" (81.0) 9/16" (14.3)B3690-4 4" (100)5/8"-11 61/8" (155.6) 11/4" (31.8) 37/8" (98.4) 9/16" (14.3)B3690-55" (125) 5/8"-11 63/4" (171.4) 11/2" (38.1) 4" (101.6) 9/16"(14.3)B3690-6 6" (150) 3/4"-10 73/4" (196.8) 13/16" (30.2) 47/16"(112.7) 9/16" (14.3)B3690-8 8" (200) 3/4"-10 91/4" (234.9) 1"(25.4) 415/16" (125.4) 9/16" (14.3)
Design Load Wt./CPart No. Bolt Size Lbs. kN Lbs. kg
B3690-1/2 1/4"-20 x 2" 400 (1.78) 20 (9.1)B3690-3/4 1/4"-20 x21/4" 400 (1.78) 23 (10.4)B3690-1 1/4"-20 x 21/2" 400 (1.78) 24(10.9)B3690-11/4 1/4"-20 x 23/4" 400 (1.78) 27 (12.2)B3690-11/21/4"-20 x 3" 400 (1.78) 29 (13.1)B3690-2 1/4"-20 x 31/2" 400 (1.78)32 (14.5)B3690-21/2 3/8"-16 x 41/2" 800 (3.56) 71 (32.2)B3690-33/8"-16 x 5" 800 (3.56) 77 (34.9)B3690-31/2 3/8"-16 x 51/2" 800(3.56) 84 (38.1)B3690-4 3/8"-16 x 61/2" 800 (3.56) 139(63.0)B3690-5 3/8"-16 x 71/2" 800 (3.56) 166 (75.3)B3690-6 3/8"-16x 81/2" 1000 (4.45) 226 (102.5)B3690-8 3/8"-16 x 101/2" 1200 (5.34)332 (150.6)
B3690C B3690F
Pip
e H
angers
Pipe Hangers
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
39
Material: SteelStandard Finish: Plain, Electro-Plated,Dura-Green, Hot-Dip Galvanized or Stainless SteelService: Designedfor suspending non-insulatedstationary pipe allowing for verticaladjustment.Ordering: Specify part number and finish.Approvals:Underwriter's Laboratories Listed for3/4" (20) thru 12" (300).Complies with FederalSpecification WW-H-171E & A-A-1192A Type 1andManufacturers Standardization Society MSS SP-69& SP-58 Type1.For AWWA - Ductile Iron, see B3102, page 44.Note: When usingoversized clevis hangers, installB3100PS (Pipe Sleeve) over crossbolt to prevent deformation of clevis bottom.
When attaching seismic bracing to clevis hangers,a B3100PS (PipeSleeve) must be installed over thecross bolt (see SeismicRestraints Brochure). Order pipe sleeves B3100PS-(pipesize)separately.
Figure B3100 Standard Clevis Hanger(Available with plasticcoating as B3100C-size or felt lined as B3100F-Size)
'B'
'D'
'C'
'E'
'A'(Rod Size)
Hanger RodNot Included
'B'Bottom of pipe
to top of hanger.
'C'Center of pipe
to top of hanger.
'D'Rod Take-Out
Center of pipe tobottom of hanger rod.
'E'Minimum thread
length of hanger rod
'F'Adjustment
Top of cross bolt tobottom of hanger rod nut
inside the hanger.
Nominal Rod SizePart No. Pipe Size 'A' B C
B3100-1/2 1/2" (15) 3/8"-16 21/8" (54.0) 111/16" (42.9)B3100-3/43/4" (20) 3/8"-16 27/16" (61.9) 17/8" (47.6)B3100-1 1" (25) 3/8"-16213/16" (71.4) 21/8" (54.0)B3100-11/4 11/4" (32) 3/8"-16 37/16"(87.3) 29/16" (65.1)B3100-11/2 11/2" (40) 3/8"-16 4" (101.6)` 3"(76.2)B3100-2 * 2" (50) 3/8"-16 41/2" (114.3) 31/4"(82.5)B3100-21/2 * 21/2" (65) 1/2"-13 59/16" (141.3) 4"(101.6)B3100-3 * 3" (80) 1/2"-13 63/4" (171.4) 47/8"(123.8)B3100-31/2 31/2" (90) 1/2"-13 7" (177.8) 5" (127.0)B3100-4 *4" (100) 5/8"-11 713/16" (198.4) 51/2" (139.7)B3100-5 * 5" (125)5/8"-11 91/16" (230.2) 61/8" (155.6)B3100-6 * 6" (150) 3/4"-10107/16" (265.1) 615/16" (176.2)B3100-8 8" (200) 3/4"-10 123/4"(323.8) 83/8" (212.7)B3100-10 10" (250) 7/8"-9 151/4" (387.3)913/16" (249.2)B3100-12 12" 300) 7/8"-9 175/8" (447.7) 113/16"(284.2)B3100-14 14" (350) 1"-8 199/16" (496.9) 121/2"(317.5)B3100-16 16" (400) 1"-8 217/16" (544.5) 135/16"(338.1)B3100-18 18" (450) 1"-8 25" (635.0) 157/8" (403.2)B3100-2020" (500) 11/4"-7 271/2" (698.5) 173/8" (441.3)B3100-24 24" (600)11/4"-7 313/4" (806.4) 195/8" (498.5)B3100-30 30" (750) 11/4"-7387/8" (987.3) 233/4" (603.2)B3100-36 36" (900) 11/4"-7 46"(1168.4) 2713/16" (706.4)
*Slide-Rite Clevis Hangerdesign, as shown above, forsizes 2,21/2, 3, 4, 5 & 6.Pat. No. 5,848,770
5,924,655
Pip
e H
angers
Pipe Hangers
40
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwisespecified.
Figure B3100 Standard Clevis Hanger (continued)(Available withplastic coating as B3100C-size or felt lined as B3100F-Size)
'B'Bottom of pipe
to top of hanger.
'C'Center of pipe
to top of hanger.
'D'Rod Take-Out
Center of pipe tobottom of hanger rod.
'E'Minimum thread
length of hanger rod
'F'Adjustment
Top of cross bolt tobottom of hanger rodnut inside thehanger.
Rod Take-Out Adjustment Design Load Wt./CPart No. 'D' 'E' 'F'Lbs. kN Lbs. kg
B3100-1/2 15/16" (23.8) 21/2" (63.5) 7/16" (11.1) 730 (3.25) 25(11.3)B3100-3/4 11/8" (28.6) 21/2" (63.5) 1/2" (12.7) 730 (3.25) 29(13.1)B3100-1 13/8" (34.9) 21/2" (63.5) 5/8" (15.9) 730 (3.25) 35(15.9)B3100-11/4 113/16" (46.0) 21/2" (63.5) 7/8" (22.2) 730 (3.25)40 (18.1)B3100-11/2 21/4" (57.1) 21/2" (63.5) 13/16" (30.2) 730(3.25) 42 (19.0)B3100-2 * 21/2" (63.5) 21/2" (63.5) 15/8" (41.3)730 (3.25) 52 (23.6)B3100-21/2 * 31/16" (77.8) 21/2" (63.5) 2"(50.8) 1350 (6.00) 90 (40.8)B3100-3 * 315/16" (100.0) 21/2" (63.5)2" (50.8) 1350 (6.00) 110 (49.9)B3100-31/2 41/16" (103.2) 21/2"(63.5) 2" (50.8) 1350 (6.00) 142 (64.4)B3100-4 * 43/8" (111.1)21/2" (63.5) 2" (50.8) 1430 (6.36) 132 (59.9)B3100-5 * 5" (127.0)21/2" (63.5) 2" (50.8) 1430 (6.36) 215 (97.5)B3100-6 * 511/16"(144.5) 3" (76.2) 2" (50.8) 1940 (8.63) 320 (145.1)B3100-8 71/8"(181.0) 31/2" (88.9) 25/16" (58.7) 2000 (8.89) 485 (220.0)B3100-1083/8" (212.7) 31/2" (88.9) 25/16" (58.7) 3600 (16.01) 846(383.7)B3100-12 911/16" (246.1) 31/2" (88.9) 25/8" (66.7) 3800(16.90) 1083 (491.2)B3100-14 105/8" (269.9) 4" (101.6) 27/8" (73.0)4200 (18.68) 1432 (649.5)B3100-16 119/16" (293.7) 4" (101.6)211/16" (68.3) 4600 (20.46) 2200 (997.9)B3100-18 143/16" (360.3)41/2" (114.3) 315/16" (100.0) 4800 (21.35) 2500 (1134.0)B3100-20165/8" (422.3) 5" (127.0) 53/8" (136.5) 4800 (21.35) 4400(1995.8)B3100-24 185/8" (473.1) 5" (127.0) 53/8" (136.5) 4800(21.35) 5000 (2268.0)B3100-30 223/4" (577.8) 5" (127.0) 61/4"(158.7) 6000 (26.69) 6600 (2993.7)B3100-36 25" (635.0) 5" (127.0)57/16" (138.1) 6000 (26.69) 8474 (3843.8)
'B'
'D'
'C'
'E'
'A'(Rod Size)
H
![B-LINE HANGER AND SUPPORTS - [PDF Document] (2024)](data:image/png;base64,iVBORw0KGgoAAAANSUhEUgAAAAEAAAABCAQAAAC1HAwCAAAAC0lEQVR42mP8/h8AAvMB+NzmkbcAAAAASUVORK5CYII=)